How often should you inspect Pilates equipment?

Updated

Regular inspections keep three things in good shape: your clients, the experience they come back for, and the equipment you've invested in. A worn spring is a safety risk, a squeaking wheel or sticky carriage is what clients notice in class, and small problems caught early cost far less than a machine that wears out years before it should.

Your manufacturer's manual is the first authority, and the major manufacturers publish their own schedules. We've gathered them in one place on the manufacturers page. They differ in the details but agree on the shape, and the schedule below follows it.

The short answer

How oftenWhat to check
WeeklySprings, rails and wheels
MonthlyHooks, clips, bolts, footwork and straps test, frame
Every three monthsSprings rotated; wheel bushings greased (classical only)
YearlyDeep check, scheduled part replacements, the year's history reviewed

Separately from inspections, replace every spring every two years, or sooner with heavy use. More on that below.

Write each one down, with the date and who did it. The record is what shows trends and patterns, like a spring that is worn out or a set of ropes that frays before the others.

Between inspections, anyone who notices something wrong, such as a new noise, a frayed strap or a footbar that won't lock, should know exactly where to report the observation so it can be flagged for the next inspection.

Weekly: springs first

Merrithew, Gratz and BASI all ask for a weekly spring inspection, and Balanced Body asks for weekly or monthly depending on how much the equipment is used. Weekly is the safe default.

  • Springs, from underneath. Look along each spring for gaps between the coils, kinks, rust and wear at the hooks. If you see any of these, even a slight gap, stop using that spring now and replace it. Don't wait for the next inspection.
  • Rails and wheels. Wipe the rails and clean the wheels with a soft, damp cloth.

Monthly: hands on

Once a month, someone goes over each machine properly, with hands and a light, not just eyes.

  • Eye bolts, spring hooks and spring clips. Check for bending, wear grooves and loose fixings, and that every clip is fastened properly.
  • Footwork and feet in straps. On a reformer, do a short set of footwork, then feet in straps. Feel and listen for bumps, thumps, squeaks or any catch from the carriage wheels or pulleys.
  • Nuts, bolts and screws. Check and tighten them, including the push-through bar and any swing on a Cadillac.
  • Frame. Look for cracks, especially on wooden equipment.
  • Towers and Cadillacs. Check the push-through bar is secure and moves without noise, and look over its safety strap for frayed stitching or webbing.

Every three months

  • Rotate springs. Swap springs of the same weight between positions so they wear evenly. Balanced Body, Align-Pilates and Your Reformer all recommend it.
  • Wheel bushings (classical equipment only). Clean and grease them with the grease your manufacturer names, as Gratz recommends. Contemporary reformers usually have sealed bearings and need nothing.

Yearly: the deep inspection

Once a year, every machine gets a thorough inspection, often by a technician or someone with experience of that brand. It's a good time to:

  • Replace parts your manufacturer schedules for yearly replacement, even if they look fine. Merrithew replaces all spring clips every year, and Align-Pilates replaces carriage wheels after a year of use.
  • Replace ropes, straps and loops that are worn.
  • Check every fastener, wheel and bearing, and service anything the manual says to service yearly.
  • Look at the machine's history across the year: anything that was flagged more than once deserves a closer look.

Many studios tie this to a date they'll remember, such as the start of the year or a quiet month.

Every two years: replace the springs

Springs lose tension gradually, so they can look fine and still be past their safe life. That's why manufacturers give a replacement interval as well as signs to look for.

  • Every manufacturer that publishes an interval says two years. Balanced Body, Align-Pilates and BASI add "or 3,000 hours of use, whichever comes first".
  • Busy studios replace sooner. Balanced Body recommends every year for group classes. Align-Pilates' warranty drops to one year for studios with six or more reformers. Gratz says 18 months with consistent use.
  • It can affect your warranty. Merrithew, BASI and Elina say not replacing springs every two years may void it. Align-Pilates' US distributor adds that it's likely to invalidate a studio's commercial insurance.

A useful reference: 3,000 hours over two years is about 29 hours a week. A machine used more than that reaches 3,000 hours before its second birthday, so count hours as well as months.

Keep a record of when each spring was installed, so you know when a set is due even if it looks fine. When you replace one, note which spring, on which machine, and the date. Over time that tells you how long springs actually last in your studio. The manufacturers page lists every brand's interval side by side.

A word on lubrication

Don't lubricate anything unless your manufacturer's manual says to. Brands disagree here, and the wrong product can damage the equipment:

  • Balanced Body, Align-Pilates, Peak and Merrithew say not to lubricate the rails, and that wheel bearings are sealed and need nothing. Balanced Body warns against spraying silicone near the wheels, and Merrithew against oil.
  • Gratz greases the inner wheel bearing only, every three months, with a specific grease.
  • Elina recommends silicone spray on its own wheels and guides.

What's right for one brand is wrong for another. Check your manufacturer's care guidance before reaching for a can.

What to do when you find something

  1. Take the machine out of use if the problem could affect safety.
  2. Record what you found, with a photo if you can.
  3. Fix it, or arrange for someone who can.
  4. Record the repair or replacement, then put the machine back in service.

Keeping inspections, flags and repairs in one place means the next person to look at that machine can see its whole history, not just today's condition.

Always follow your equipment manufacturer's instructions. This page doesn't replace them, and if the two differ, the manufacturer's guidance comes first.

Keep every inspection on record.

Hooke's Log is free for up to 5 pieces of equipment. Log checks, flag issues and keep every spring's replacement history in one place.

Start your free log